Tracking Code
3230-015
Job Description
Basic Function
Performs general labor as assigned.If demolding:
Removes finished foam seating pads from their molds, places parts on a conveyer for the next stage of the finishing process and
removes any obvious foam particles from the molds.
If waxing:Removes any obvious foam particles from molds and applies a thin layer of demolding agent (aerosol wax) to the surface of the molds.
Verified by Reference Check or Job Performance
•Able to work in team setting and communicate well
•Physically able to perform job
•Follows both oral and written instructions, including customer standards.4. Reliable
•Able to work any shift and overtime as directed
•Follows good safety practices.
If Waxing:
•Able to operate and properly calibrate aerosol wax gun
•Must be proficient in knowledge and application of all applicable standards and work instructions pertaining to the specific parts assigned.
If Repairing:Specific Duties
All positions clean work area during periods of downtime and at the conclusion of shift and perform various duties assigned by supervisor.
Performs production-related duties as assigned: Waxing:
•Cleans foam particles and/or wax build-up from molds
•Applies spray wax to the mold surfaces
•Notifies supervisor and line technician of process problems
Placing Inserts:
•Places proper inserts (wires, felts, & Velcro) into molds.
•Informs supervisor of insert shortages; assists in recovering dropped or misplaced inserts
Demolding:
•Removes molded foam seat pads from molds.
•Places part on conveyer for next stage of finishing process.
•Cleans any foam particles and/or wax build-up from the molds.
•Informs supervisor and line technician of process problems underfills, wax burns, etc.
Trimming:
•Removes all ribbon vents and uncontrolled flash on parting line that is greater than 25mm using scissors or air trimmer tool.
•Inspects parts for the following defects.
•Flash not trimmed off.
•Hard spots on the parting line.
•Under fills
•Foam free areas
•Safety glove must be worn on opposite hand.
•Inform supervisor of B-surface defects.
**" percent of time spent in working environment or using physical demands
•See specialized customer required trim areas.
Repairing:
•Look for voids marked by Inspector.
•Use scoop to repair.
•If voids are small, stuff the void with repair foam, then cut it back to contour of part.
•Inform supervisor of any insert shortages
Packing:
•Remove parts off the monorail.
•Identify part, place it in its respective bin
•Pack the parts in their respective order. The pack description is posted on the floor where the bins go.
•Pack description includes the part orientation
•Pack description includes the quantity
•Pack description includes the part number and the vehicle
•Verify th8t the standard pack is met.
•Verify the correct quantity is in the bin
•Verify that the pack orientation is correct
•Make sure that all parts are inside of the bin. Parts that hang out of the bin may get ripped.
•Notify production supervisor if out of balance on parts.
•As backup to material clerk, prepare and attach product labels.
Mold Cleaning:
•Clean the bowl of the tool.
•Clean all ribbon vents of any foam
•Clean any areas that have foam stuck to them
•Apply paste wax to any areas scrubbed with a chore boy or had stuck foam
•Clean all wire holders of foam.
•Apply paste wax to wire holders that have stuck foam
•Vent Identification
•Ribbon Vent
•Verify the bowl is clean.
•Inspect the ribbon vents to ensure they are free of flash
•Inspect all wire holders to ensure they are foam free. A foamed in holder
Required Skills
Qualifications: Skills, Education and Training Required
Environmental management system overview Orientation
Quality Management System Overview Right-to-Know/Hazardous Communication
Job Location
Farwell, Michigan, United States
Position Type
Full-Time/Regular
Authorization Number
N/A
We are an equal opportunity employer with a commitment to diversity. All individuals, are encouraged to apply.